arduino
I2C-communicatie

Invoering

Meerdere slaven

Het volgende voorbeeld laat zien hoe de master gegevens van meerdere slaves kan ontvangen. In dit voorbeeld stuurt de slaaf twee korte nummers. De eerste is voor temperatuur en de tweede is voor vocht. Merk op dat de temperatuur een vlotter is (24.3). Om slechts twee bytes te gebruiken en niet vier (float is vier bytes), vermenigvuldig ik de temperatuur in 10 en sla deze op als een short. Dus hier is de mastercode:

#include <Wire.h>

#define BUFFER_SIZE  4
#define MAX_NUMBER_OF_SLAVES 24
#define FIRST_SLAVE_ADDRESS 1
#define READ_CYCLE_DELAY 1000

byte buffer[BUFFER_SIZE];

void setup()
{
  Serial.begin(9600);  
  Serial.println("MASTER READER");
  Serial.println("*************");
  
  Wire.begin();        // Activate I2C link
}

void loop()
{
  for (int slaveAddress = FIRST_SLAVE_ADDRESS; 
       slaveAddress <= MAX_NUMBER_OF_SLAVES; 
       slaveAddress++) 
  { 
    Wire.requestFrom(slaveAddress, BUFFER_SIZE);    // request data from the slave
    if(Wire.available() == BUFFER_SIZE)
      {  // if the available data size is same as I'm expecting
        // Reads the buffer the slave sent
        for (int i = 0; i < BUFFER_SIZE; i++) 
        {
          buffer[i] = Wire.read();  // gets the data
        }

        // Parse the buffer
        // In order to convert the incoming bytes info short, I use union
        union short_tag {
          byte b[2];
          short val;
        } short_cast;

        // Parse the temperature
        short_cast.b[0] = buffer[0];
        short_cast.b[1] = buffer[1];
        float temperature = ((float)(short_cast.val)) / 10;

        // Parse the moisture
        short_cast.b[0] = buffer[2];
        short_cast.b[1] = buffer[3];
        short moisture = short_cast.val;

        // Prints the income data
        Serial.print("Slave address ");      
        Serial.print(slaveAddress);
        Serial.print(": Temprature = ");
        Serial.print(temprature);
        Serial.print("; Moisture = ");
        Serial.println(moisture);
      }
    }
    Serial.println("*************************");
  
    delay(READ_CYCLE_DELAY);
  }
}

En nu de slave-code:

#include <Wire.h>
#include <OneWire.h>
#include <DallasTemperature.h>

//=====================
// This is the hard-coded address. Change it from one device to another
#define SLAVE_ADDRESS 1
//=====================

// I2C Variables
#define BUFFER_SIZE 2
#define READ_CYCLE_DELAY 1000
short data[BUFFER_SIZE];

// Temprature Variables
OneWire oneWire(8);
DallasTemperature temperatureSensors(&oneWire);
float m_temperature;

// Moisture Variables
short m_moisture;

// General Variables
int m_timestamp;

void setup()
{
  Serial.begin(9600);  
  Serial.println("SLAVE SENDER");
  Serial.print("Node address: ");
  Serial.println(SLAVE_ADDRESS);
  Serial.print("Buffer size: ");
  Serial.println(BUFFER_SIZE * sizeof(short));
  Serial.println("***********************");

  m_timestamp = millis();
  Wire.begin(NODE_ADDRESS);  // Activate I2C network
  Wire.onRequest(requestEvent); // Set the request event handler
  temperatureSensors.begin();
}

void loop()
{ 
  if(millis() - m_timestamp < READ_CYCLE_DELAY) return;

  // Reads the temperature
  temperatureSensors.requestTemperatures();
  m_temperature = temperatureSensors.getTempCByIndex(0);

  // Reads the moisture
  m_moisture = analogRead(A0);
}

void requestEvent()
{
  data[0] = m_temperature * 10; // In order to use short, I multiple by 10
  data[1] = m_moisture;
  Wire.write((byte*)data, BUFFER_SIZE * sizeof(short));  
}